Model Number : N1005G-2PD

5 Port POE Gigabit SW with 802.3af/at *2 Port and PD Source Port *1

PCBA Model : BXS-1212

Only PCBA Board

Introduction

The 5Port POE Gigabit Switch is a powerful and supports IEEE 802.3af/at standard high-performance Gigabit Extender switch provides DC 42~57V Gigabit over Ethernet cables. It also has the ability to pass-through PoE power further downstream to one or two Powered Devices (PD devices) and the PoE budget is dependent on the PoE source (802.3af or 802.3at) and the PD’s PoE Classification. It is ideal to extend the Ethernet network range beyond 100m, delivering both data and power to network devices. Moreover, it supports dual power receiving mode PoE(PD) In and DC In. User can select either one to supply power or it can choice dual power supply as power backup function for the device. (Power failover). It supports 5 ports 10/100/1000Mbps auto-negotiation function including 2 Ports 10/100/1000M Gigabit port Power over Ethernet (PoE+). It’s through RJ45 UTP network is to transmit power and data to meet the requirements.

Highlight Features

  • Complying with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, IEEE 802.3af PoE and IEEE 802.3at PoE+
  • 5 Ports 10/100/1000Mbps Auto-Negotiation Gigabit Switch, including 1 Port PD + 2 Ports PSE/ PoE Extension function, complying with IEEE 802.3af/at standard
  • Supports dual power receiving mode PoE(PD) In and DC In. It supports power backup function when use dual power supply (Power Failover)
  • Full/Half-Duplex capability on each TX port ,
  • Supports Store & Forward architecture and performs forwarding and filtering
  • Auto-learning networking configurations
  • Supporting the flow control: back pressure for Half-duplex and IEEE 802.3x for Full-duplex mode
  • Supports Jumbo Frame 9K
  • Non-blocking & Non-head-of-line blocking full-wire speed forwarding
  • Supports TP interface Auto MDIX function for auto TX/RX swap
  • Automatic Source MAC Address Learning and Aging
  • Supports up to 2K MAC addresses and Up to 1Mb bits buffer
  • Support desktop and wall mounting

Hardware Specification

 
Product 5 Port POE Gigabit SW with 802.3af/at *2 /4Port and PD Source Port *1
Standard IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3ab 1000BASE-T

IEEE 802.3af Power over Ethernet (PoE)

IEEE 802.3at Power over Ethernet (PoE+)

Port Configuration 5ports RJ-45 connectors for 10/100/1000Mbps

With 1 Port PD & 2 Ports PSE/ PoE+

Network Media 10BASE –T: UTP Cat. 3 or up,

100BASE-TX: UTP Cat. 5 or up,

1000BASE-T: UTP Cat. 5 or up

Data Transfer Rate 10/100/1000Mbps (Half-duplex),

20/200/2000Mbps (Full-duplex)

PoE Type PSE : End-span (Type-A): PIN 1/2,3/6

PD : End-span (Type-A): PIN 1/2,3/6 or

Mid-span (Type-B): PIN 4/5,7/8

Max PoE Up to 30Watt per port
Power Interface Input : DC In and RJ45 PoE(PD) In

Output : RJ45 PoE out

Power Requirement External Power Supply, Input Voltage: 42 ~ 57Volt or

802.3af/at PoE Power Source

Power Consumption 1.5Watt
Power Supply Optional
MAC Address Table 2K
Built-in Buffer 1Mb
Jumbo Frame 9K
LED Definition Power/System: LED x1

l Power On: Green

l Power Off: LED off

PoE (PSE) Status: LED x2

l PoE Link/ACT: Green

l PoE Disconnection : LED off

PoE (PD) Status: LED x1

l PoE Link/ACT: Green

l PoE Disconnection : LED off

Ethernet Port LED x5

l 10/100M Link/ACT : Orange

l 10/100/1000M Link/ACT : Green

Temperature Operating : 0° to 50° C

Storage: -40° to 70° C

Humidity 5% to 90% non-condensing
Dimension

( W x D x H )

N1005G-2PD : 160*85*25 mm

BXS-1212 : 150*80 mm

Weight N1005G-2PD : 334.4g

BXS-1212 : 87.2g

Case of material Metal
Certifications FCC ,CE, RoHs compatible

**Specifications can be negotiated separately according to needs